MODEL 86 DRUM LIFTER

• Transports drums in the upright position
• Designed for plastic and fiber drums 
  with 22" to 23½" diameters and 23" to 38" high
• Drum is supported on bar at the bottom
• Drum is secured in saddle with chain and ratchet
• Attaches to a monorail, crane, or chain block
• Capacity: 1,000 Lb. (454 kg)

Models 90, 91, & 92

MODEL 90 VERTI-KARRIER

• GRAB, LIFT, MOVE, and PLACE DRUMS ALMOST ANYWHERE
• Load drums into remote or hard-to-reach areas
  1. Attach the Verti-karrier to your hoist
  2. Move the Karrier to drum and then lift
  3. It grips automatically
  4. Releases the load when the drum is set down. 
  Grip will not disconnect until the drum is fully down.
• The operator's only duties are to operate the hoist and guide the grab into position. Moving drums to and from difficult locations saves operator and equipment time, and protects against dangerous climbing. The grab mechanism is simple.
• Capacity: 1,000 Lb. (454 kg)
• Not for drums without lids or tops in place.
• Model 90-M sis same karrier with spark resistant parts.

MODEL 90-30 VERTI-KARRIER (not shown)
Similar to model 90, but sized for typical 30 gallon steel drums. Not for drums without lids or tops in place.

MODEL 90-85 VERTI-KARRIER (not shown)
Similar to model 90, but sized for typical 85 gallon steel overpack or salvage drums. Not for drums without lids or tops in place.

MODEL 91 LIFTER FOR DRUMS and OVERPACKS

• For placing 55 gallon (210 liter) steel drums into overpack or salvage drums.
• Can also lift 85 gallon steel overpack drums.
• Effective and simple to use with carefully designed ice-tong-like geometry and broad faced, thin profile grippers.
• Broadness of grippers spreads holding force to minimize pressure on drum.
• Narrow profile enables it to lower the drum completely into the overpack.
• Can also be used to lift and move the closed salvage drum.
• Capacity: 1,000 Lb. (454 kg)
• Shipping weight 18.5 lb. Class 77.5 by truck, UPS and RPS. Fully assembled in 20" x 9" x 17" carton.

• Latest of Morse "Below the Hook" lifters.
• Has self-adjusting tong-like action
• Automatically grips various common types of closed steel, fibre or plastic drums.
• 18" to 26" diameter range includes many lever-lock closure fibre drums, typical steel drums and rimmed plastic drums in 30 to 55 gallon sizes.
• Also handles 85 gallon steel salvage or overpack drums. (not for plastic overpacks)
• Can be used to lift drums to or from four-drum pallets or rows of adjacent drums.
• Capacity: 1,000 Lb. (454 kg)

NOTE:

• Drum rim must be within 1" from the top of the drum.
• Weight of drum contents must not exceed the drum manufacturer's packing limit.
• Drum lid must be properly secured.

Shipping weight 25 lb. Class 77.5 by truck, UPS and RPS. Fully assembled in 20" x 9" x 17" carton.

MODEL 41 DRUM LIFTING HOOK

• Model 41 lifts horizontal 55 gallon (210 liter) steel drums, 34-36" (86-92 cm) long
• Alloy steel lifting ring, steel rods, malleable iron hooks
• Capacity: 1,000 Lb. (454 kg)

MODEL 41-M SPARK RESISTANT DRUM LIFTING HOOK

• Lifts horizontal 55 gallon (210 liter) steel drums
• Similar to 41 but made of bronze and copper for spark-resistance
• Capacity 750 Lb. (340 kg)

MODEL 42
WITH HORIZONTAL DRUM

MODEL 42
WITH DRUM IN OFF-VERTICAL POSITION

MODEL 42 DRUM LIFTER

• Heavy duty drum lifter for use on a hoist hook or fork mounted hook.
• Made with a pair of forged hooks for engaging the rims at opposite ends of the drum.
• Pair of alloy steel lifting rings provides for two modes of lifting:
  1. Drum horizontal
  2. Drum in off-vertical
• Enables upending and downending drums.
• Lower drum until its bottom corner meets the floor, then guide drum to settle upright or allow it to tilt down to horizontal.
• Alloy chain, alloy links and alloy lifting rings are combined with heavy duty steel rod with welded eyes to provide a heavy duty assembly. The forged steel hooks are shaped to engage drum rims.
• Capacity: 2,000 Lb. (909 kg)
• Model 42 is self-colored, without blue paint
• Model 42-G is same style lifter with hot dip galvanized finish

Model 284 Fork Hook (shown on fork)

Being used with Model 42 Drum Lifting Hook (shown on drum)

• Model 284 fork mounted hook slides right onto the fork to enable use of Morse below hook drum lifters
• Fork opening is 5-1/2" X 1-9/16"
• Capacity:  2,000 Lb. (909 kg)

Morse below-the-hook drum lifters (i.e. Models 85A, 185A, 90, 41, etc.) are manufactured by Morse Mfg. Co., Inc. in East Syracuse, NY 13057. These drum lifters comply with ANSI/ASME B30.20 standard for mechanical, below-the-hook lifting devices as it applies to the following:

• Rated load markings and unit identification
• Minimum design safety factor of 3, based on yield strength, for load bearing structural components
• Welding is performed by certified welders who have passed the ANSI/AWS D1.1 welding qualification test